E-mail: amy@bjgreenpower.com   WhatsApp/wechat: +8618500983665 Chinese
Home > News > Content
Rectifier Output Smoothing
Dec 28, 2017


This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed(October 2017) (Learn how and when to remove this template message)

It has been suggested that Ripple (electrical)#Ripple voltage be merged into this section. (DiscussProposed since November 2017.

The AC input (yellow) and DC output (green) of a half-wave rectifier with a smoothing capacitor. Note the ripple in the DC signal.

While half-wave and full-wave rectification deliver unidirectional current, neither produces a constant voltage. There is a large AC ripple voltage component at the source frequency for a half-wave rectifier, and twice the source frequency for a full-wave rectifier. Ripple voltage is usually specified peak-to-peak. Producing steady DC from a rectified AC supply requires a smoothing circuit or filter. In its simplest form this can be just a capacitor (also called a filter, reservoir, or smoothing capacitor), choke, resistor, zener diode & resistor, or voltage regulator placed at the output of the rectifier. In practice, most smoothing filters utilize multiple components to efficiently reduce ripple voltage to a level tolerable by the circuit.

Full-wave diode-bridge rectifier with parallel RC shunt filter


The filter capacitor releases its stored energy during the part of the AC cycle when the AC source does not supply any power, that is, when the AC source changes its direction of flow of current.


Performance with low impedance source[edit]

Reservoircapidealised.gif

The above diagram shows reservoir performance from a near zero impedance source, such as a mains supply. As the rectifier voltage increases, it charges the capacitor and also supplies current to the load. At the end of the quarter cycle, the capacitor is charged to its peak value Vp of the rectifier voltage. Following this, the rectifier voltage starts to decrease to its minimum value Vmin as it enters the next quarter cycle. This initiates the discharge of the capacitor through the load.

The size of the capacitor C is determined by the amount of ripple r that can be tolerated, where r=(Vp-Vmin)/Vp.[7]

These circuits are very frequently fed from transformers, and have significant resistance. Transformer resistance modifies the reservoir capacitor waveform, changes the peak voltage, and introduces regulation issues.


Capacitor input filter[edit]

It has been suggested that Filter capacitor be merged into this section. (DiscussProposed since November 2017.

It has been suggested that Capacitor-input filter be merged into this section. (DiscussProposed since November 2017.

For a given load, sizing of a smoothing capacitor is a tradeoff between reducing ripple voltage and increasing ripple current. The peak current is set by the rate of rise of the supply voltage on the rising edge of the incoming sine-wave, reduced by the resistance of the transformer windings. High ripple currents increase I2R losses (in the form of heat) in the capacitor, rectifier and transformer windings, and may exceed the ampacity of the components or VA rating of the transformer. Vacuum tube rectifiers specify the maximum capacitance of the input capacitor, and SS diode rectifiers also have current limitations. Capacitors for this application need low ESR, or ripple current may overheat them. To limit ripple voltage to a specified value the required capacitor size is proportional to the load current and inversely proportional to the supply frequency and the number of output peaks of the rectifier per input cycle. Full-wave rectified output requires a smaller capacitor because it is double the frequency of half-wave rectified output. To reduce ripple to a satisfactory limit with just a single capacitor would often require a capacitor that's infeasibly large.

Choke input filter[edit]

It is also possible to put the rectified waveform into a choke-input filter. The advantage of this circuit is that the current waveform is smoother: current is drawn over the entire cycle, instead of being drawn in pulses at the peaks of AC voltage each half-cycle as in a capacitor input filter. The disadvantage is that the voltage output is much lower – the average of an AC half-cycle rather than the peak; this is about 90% of the RMS voltage versus {\displaystyle {\sqrt {2}}}{\sqrt {2}} times the RMS voltage (unloaded) for a capacitor input filter. Offsetting this is superior voltage regulation and higher available current, which reduce peak voltage and ripple current demands on power supply components. Inductors require cores of iron or other magnetic materials, and add weight and size. Their use in power supplies for electronic equipment has therefore dwindled in favour of semiconductor circuits such as voltage regulators.